01What this bike lets you adjust
Every change you can make to the CB500 Hornet’s suspension falls into one of the circuits below. Knowing which adjusters you actually have is the first step — there’s no point chasing a high-speed compression fix on a bike that only offers preload.
Front fork
- Low-speed compression
- High-speed compression
- Rebound damping
- High-speed rebound
- Spring preload
- Fork height (ride height)
- Spring rate (swappable)
Rear shock
- Low-speed compression
- High-speed compression
- Rebound damping
- High-speed rebound
- Spring preload
- Ride height (shock length)
- Spring rate (swappable)
Where are the exact clicker limits?
This page is the map of which adjusters the CB500 Hornet has. The factory-accurate number of clickson each one — so you always know your range and never wind past a stop — lives in the Apex Wizard app, free.
02How to approach the CB500 Hornet
The CB500 Hornet has no damping clickers. That isn't a dead end — it means your setup levers are geometry, springs and pressure, and they're powerful ones.
- Preload and ride height are your primary tools. Setting sag correctly is not a preliminary step on this bike, it is the setup.
- Tyre pressure has more effect here than on any adjustable bike, because it's the only damping-adjacent variable you control. Log it every session.
- If the bike is still wrong with sag and pressure correct, the honest next step is springs matched to your weight, or a cartridge/shock upgrade — not more fiddling.
03Where to start — the baseline
Whatever the CB500 Hornet offers, the order of operations is always the same. Start from the OEM clicker baseline (count every adjuster from fully closed), set tyre pressures, then set sag before you touch a single damping clicker.
- Tyre pressure first.It moves the chassis more than any clicker. Start from a known cold target — see the track day tyre pressure guide.
- Then sag. On a naked / streetfighter machine, aim for roughly 35–40 mm of front rider sag and 30–35 mm at the rear, then verify against the manual. Full method in the sag guide.
- Then one clicker at a time. Change one thing, ride the same reference, log it. The full loop is in the suspension tuning guide.
Why these numbers for a naked
Naked bikes carry more weight over the rear and get ridden on real roads, so a slightly softer baseline with more sag keeps them compliant without going vague.
04What you can't tune on the CB500 Hornet
Knowing where the CB500 Hornetstops adjusting saves more time than any clicker chart. These are the fixes this bike can’t make with a screwdriver — and what to reach for instead:
- No front damping adjustment — fork dive and front-end harshness have to be managed with preload, fork height, spring rate and tyre pressure.
- No rear damping adjustment — squat and rear grip come from preload, ride height and pressure alone.
05Match the symptom to the adjuster
On the CB500 Hornet, as on any bike, diagnose by the corner phase where the problem shows up — not the symptom alone. Ordered by what this bike can actually act on:
- Setting Sag — Measure and set static and rider sag on a motorcycle — the geometry baseline every other suspension change depends on. Targets, method and mistakes.
- Tire Pressure — How to set motorcycle track day tire pressures: cold starting targets, hot pressure gain, and why pressure comes before any clicker change.
- Cold vs Hot Tear — Cold tear and hot tear look similar but mean opposite things. Read motorcycle tire wear patterns and what each says about pressure, temperature and setup.
- Running Wide — A motorcycle that runs wide on entry is a different problem from one that runs wide on exit. Diagnose by corner phase and find the adjuster that fixes it.
06Honda CB500 Hornet setup FAQ
What suspension adjustments does the Honda CB500 Hornet have?
Up front the CB500 Hornet offers spring preload, fork height (ride height) and spring rate (swappable). At the rear it offers spring preload, ride height (shock length) and spring rate (swappable). Tyre pressure and chassis geometry round out the picture. Apex Wizard stores the factory-accurate clicker limits for each of these so you always know how many clicks of range you actually have.
Does the Honda CB500 Hornet have high-speed compression adjustment?
No. The CB500 Hornet uses a single compression circuit (low-speed only), and adjustment up front is limited to preload and ride height. Most riders won't miss high-speed adjustment on a road or club-level track bike.
What suspension sag should I set on the Honda CB500 Hornet?
As a starting point on a naked / streetfighter machine, aim for roughly 35–40 mm of front rider sag and 30–35 mm at the rear, then confirm against the service manual. Naked bikes carry more weight over the rear and get ridden on real roads, so a slightly softer baseline with more sag keeps them compliant without going vague. Always set sag before touching any clicker — it's the geometry baseline everything else depends on.
What should I adjust first on the Honda CB500 Hornet?
Tyre pressure, then sag, then one damping change at a time — in that order. With no damping clickers, sag and pressure aren't preliminaries here — they are the setup. Changing two things between sessions means you learn nothing from either.
What can't I adjust on the Honda CB500 Hornet?
The CB500 Hornet has no front compression, front rebound, rear compression and rear rebound adjusters, so those corrections have to come from preload, ride height, spring rate or tyre pressure instead. Most wasted setup time goes into chasing a fix the hardware can't make, so it pays to know the limits before you start.
More Honda setups
Get the Honda CB500 Hornet factory baseline.
Apex Wizard ships the CB500 Hornet's exact clicker limits and a guided setup logbook — log changes, compare sessions, and get symptom-based recommendations. Free.